- Mcculloch 10-10e
- Mcculloch Pro 10 10 Automatic
SPROCKET CHAINSAW 3/8' X 7T McCulloch 10-10, Pro Mac $ 21.15 Sale Rotary 3010. CHAINSAW STARTER SPRING ECHO 10, McCULLOCH 217482, 300474, POULAN 530091868. The McCulloch Company built and sold the Pro-Mac 10-10 chainsaw from 1977 to 1982. McCulloch, based in Sante Fe Springs, California, builds lawn and garden equipment, as well as low-voltage outdoor lighting and power tools. The McCulloch Pro-Mac 10-10 has a one-cylinder, 3.3 cubic inch engine (54 cc. The ignition coil and electronic circuitry are contained in a one-piece ignition module (10—Fig. MC130), which is serviced as a unit assembly. Air gap between the fiywheel mag- nets and the laminated legs of the mod- ule should be 0.010-0.015 in. Loosen ignition module mounting screws and move module to obtain de- sired air gap.
| You are here: Home > Parts & Tools > Chainsaws > McCulloch > McCulloch MAC 10-10 > Bar |
|
The McCulloch MAC 10-10 bar plays an important part of cutting, it guides the chain to keep it moving straight and true in the direction of the cut so the chain can cut the wood properly. The bar is made of high quality super tough chrome-moly steel. The McCulloch MAC 10-10 bar rails are heat treated to provide superior wear and bar body strength. If the chain moves side to side inside the bar, the bar rails can become chipped, the bar can be bent, at which point the McCulloch MAC 10-10 bar will need to be replaced. We offer suitable replacement chainsaw bar parts for this exact model chainsaw below. |
|
Suitable Replacement McCulloch MAC 10-10 Chainsaw Bar PartsIf the sprocket nose is broken or locked up, the bar needs to be replaced. The sole purpose of the bar is to guide the chain in the wood for a clean and straight cut. Performance Parts Supply suitable replacement chainsaw bars meet or exceed OEM specifications for McCulloch MAC 10-10 replacement bars and they cost less than OEM bars while maintaining excellent quality and durability. Chainsaw bars should either be replaced or cleaned per manufacturers specifications that are located in your owners manual. You can quickly buy our suitable replacement McCulloch MAC 10-10 Chainsaw Bar parts for sale in our online store and get it shipped fast. McCulloch MAC 10-10 Bar Lubrication AdviceThe saw uses bar oil to lube the chain and bar rails. Bar oil is designed to stick and cling to the chain and not sling off. Motor oil is not a good substitute for bar oil. Motor oil will not properly lube the chain because it is designed to separate from engine parts and drain back into the oil pan to be reused. Never attempt to use motor oil that has been used as used motor oil has dirt and other particles in it giving it a black color. Used motor oil could contain small metal pieces or shavings which would cause extreme wear on the chain and McCulloch MAC 10-10 bar and may damage your oil pump causing more costly repairs. The chain needs to be sharp to cut wood fast. Forcing the chain to cut can cause premature wear on the bar rails and stretch the chain. Our bars range in size from 10‹?? to 42‹?? with bar gauges from .043‹?? through .063‹??. If you are not sure which gauge or pitch you are running on your saw, be sure to check the chain cross over chart to determine your chain's gauge. Additionally, there may be numbers stamped into the bar that may help determine the gauge and pitch chain you will need. Remember, the best saw to cut wood should have a good sharp chain and good bar to guide the chain. McCulloch MAC 10-10 Replacement Bar Maintenance TipsThe bar may need periodic maintenance. If the rails are sharp or rolled over, they will need to be dressed up by removing the rolled edge with a file, a bar rail dresser, or a hand grinder to remove the rolled edge and true the bar rail to be square and true again. The McCulloch MAC 10-10 bar groove can become worn after use which causes the chain to roll from side to side. If this occurs, the bar should be replaced. Important Notice - We are not affiliated with any chainsaw manufacturers and we do not attempt to make any affiliations with them. Any manufacturer logos, model names and numbers are the sole property of their respective owners and are used here for the sole purpose of reference. We do not sell OEM chainsaw parts for any brand. We do however, offer high quality suitable replacement parts guaranteed to meet or beat OEM part specifications like our suitable replacement Chainsaw McCulloch MAC 10-10 Bar we offer for sale for you to buy and put into their brand of chainsaws. |
|
|
The McCulloch MAC 10-10 carburetor is designed to take gasoline liquid state and atomize the fuel with air in the proper proportion to power the chain saw motor. If the carburetor gets damaged, gummed up, or contaminated with water causing white rust white powder substance, the McCulloch MAC 10-10 carburetor will need to be replaced.
McCulloch 10-10
| Mac 1010 from '60's and 70's |
The Mac 10 series first came out in the mid 60's and were a major improvement.
'The new MAC-10 Series saws are up to 25% lighter than most so-called lightweights, yet have every feature you could ask for.' --1966 McCulloch advertisement
Well, maybe not quite every feature. By the mid-70s, the starter had been moved from the right side to the left so a chain brake could be added, and there was a more comfortable rubber-coated handle available. (These two saws are both 10-10's, but were built up from several different saws, explaining why the labels on the air cleaners are not correct.) These saws handled nicely, but vibrated so badly that your hands felt fuzzy by the end of the day, and what they lacked in power they more than made up in pure noise, even though McCulloch tried at least three different mufflers over the years.
But by this time the foreigners were here, the American manufacturers seemed to be concentrating on making toy chain saws for homeowners, OSHA had arrived and was nosing around, and it was a whole new ball game...
- - Updated 02/04/2013
- - Updated 2/08/01
Mcculloch 10-10e
Mcculloch Pro 10 10 Automatic